Overview:

The GEPRC STABLE F411 micro tower electronic system is one of the best electronic system solutions for micro quads on the market.

STABLE F411 is equipped with F411 FC, 4IN1 BLS 12A ESC and 5.8G PIT/25/100/200mW,  It supports 2-4S batteries,which could meet all kinds of demand environment. With the three-layer structure design and completely optimized pad structure, wiring is simpler and more reasonable.

STABLE F411 adopts 16*16 mm mounting holes and pin-type modular design. Supporting IRC TRAMP protocol, you can directly adjust VTX frequency, frequency and flight control parameters in the OSD interface, which is very convenient and easy to use. With LED interface, you can program your LED strip with Betaflight Ground Station. You can clearly see aircraft’s voltage, current, battery usage and other information with integrated OSD chip.

STABLE F411 is equipped with a 200 mW VTX, which can easily cope with various flight environments. While the build-in PIT mode (low power mode) is very convenient for competition use, and your VTX will not affect others when adjusting the frequency. A professional 5.8G rod antenna is equipped to achieve ideal transmission effect.

STABLE F411 supports a variety of receivers including Sbus, PPM, CRSF, DSMX, iBus protocols, which can be used with your remote control.

الميزة الرئيسية:

• MCU: STM32F411

• IMU: MPU6000 gyro/accelerometer (SPI)

• Continuous current: 12A

• Input voltage : 2-4S LIPO

• Power : PIT/25/100/200mW

• Integrated LC Filter

• Mounting holes: 16mm*16mm

• Support:Sbus,PPM,CRSF,DSMX,iBus

STABLE F411 Flight Controller(16*16mm)

• MCU: STM32F411

• IMU: MPU6000 gyro/accelerometer (SPI)

• نظام التشغيل: نظام التشغيل BetaFlight OSD مع شريحة AT7456E

• BEC Output:5V@2A

• Size: 21mm*21mm

• Mounting holes: 16mm*16mm

• Integrated LC Filter

• Input voltage 2-4S LIPO

• Firmware target: MATEKF411

• Weight: 2.5g

STABLE F411 BLheli_S 4IN1 12A ESC(16*16mm)

• MCU: BB21F16G

• Continuous current: 12A

• Input voltage : 2-4S LIPO

• ESC protocol: pwm, oneshot125, multishot, dshot150, 300, 600, etc.

• Size: 23mm*21mm

• Mounting hole: 16*16mm

• Firmware target: Blheli_S G_H_30

• Current meter: 210

• Weight: 2.7g

STABLE F411 VTX 5.8G 200mW(16*16mm)

• Power : PIT/25/100/200mW

• Antenna interface : IPEX (UFL)

• Telemetry: IRC Tramp

• Size: 17mm*27mm

• Mounting holes: 16*16mm

• Integrated LC Filter

• Weight: 1.6g

تتضمن العبوة:

• 1 x STABLE F411 Flight controller

• 1 x STABLE F411 BLheli_S 4IN1 12A ESC

• 1 x STABLE F411 VTX 5.8G 200mW

• 1 x 5.8G Antenna

• 1 x XT30 Cable

Manual Download

Mateki Stable VTX features a 5.8GHz antenna with 20mW (16×16 power output, adjustable from 25/100/200mW), utilizing an IPEX interface with a unique feature: IRC Tramp size 7mm x 27mm.

Features an integrated LC filter, with firmware optimized for Blheli_S 16.7 protocol. Specifications include: weight – 1.6g, input voltage range – 2-4S LiPO, telemetry capabilities utilizing IRC Tramp BEC, and output capacity of up to 2A. Supported ESC protocols include PWM, OneShot125, MultiShot, DSHOT150/300/600, etc.

Features a comprehensive power system with GND, +SV, 3.3v3, #5V, and GND rails, as well as a dedicated USB port for connection to the Betaflight Stable F411 Flight Controller (16x16mm).

Please note that you will need to configure the serial port (VIN points to) and choose your serial receiver provider.

Remember to configure the Serial Port via the Ports tab and choose your Serial Receiver Provider when using the RX_SERIAL feature. Additionally, note that this flight controller supports GND FrSky FPort serial-based receivers (compatible with Spektrum SAT and SBUS modes 8).

Remember to configure the Serial Port via the Ports tab, and select the Serial Receiver Provider. Additionally, note that this flight controller supports Spektrum2048 serial receiver provider, along with features such as GND SV Buzz LED, 3.3V R2 nT2 GND WIDEO T2 (compatible with S-BUS).

Target configuration for this ESC: BLheli_S 16.7, compatible with G-H-30 motors (4-in-1), IQ 0 O 0, and supports 2-4S Lipo battery configurations.

Note that the VTX Button must be installed before powering on. If you intend to use the button with Betaflight Ports v3.3.0 or later, please disable the IRC TRAMP peripherals UART3.

Do not disable MSP on the first serial port unless you know what you’re doing, as reflashing and modifying your configuration may be required. Ensure that your configuration identity matches.